Planet ADN-4000 Instrukcja Użytkownika

802.11n Wireless ADSL 2/2+ Router ADN-4000 User's Manual

BLINKING WPS function is enabled ON Connected to an ADSL DSLAN successfully ADSL BLINKING No Connection ON The LAN cable is connected to the router OF

2 Installation This chapter offers information about installing your router. If you are not familiar with the hardware or software parameters presente

Select a suitable place on the network to install the ADN-4000. NOTE For best Wireless reception and performance, the ADN-4000 should be positione

2.3 Configuring the Network Properties Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-

4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address auto

Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2.

Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration

3 Configurations 3.1 Determine your connection settings Before you configure the router, you need to know the connection information supplied by your

Home Screen 19

Copyright Copyright© 2008 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed

3.3.1 Quick Start You can use "Setup Wizard" to setup the router as follows, and the router will connect to the Internet via ADSL line. Cl

Step 2 - Click "Next" to setup your new administrator's password. Step 3 - Click "Next" to setup your time zone. Step 4 - C

Step 5 - Enter the connection information provided by your ISP. Step 6 - The Setup Wizard has completed. If you have any change or mistake, click “B

Step 7 - Saved Changes. 3.4 Interface Setup 3.4.1 WAN Configuration Go to Interface Setup -> Internet. The router can be connected to your se

3.4.1.1 ATM VC ATM settings are used to connect to your ISP. Your ISP provides VPI, VCI, settings to you. In this Device, you can totally setup 8 PVCs

CBR is for connections that support constant rates of data transfer. The only parameter you need to worry about in CBR is PCR. UBR is for connections

VPI Enter your VPI number here. VCI Enter your VCI number here. ATM QoS Select the QoS type for the PVC in question from the dropdown list. PCR Enter

The following table describes the labels in this screen. Parameter Description Encapsulation Select your encapsulation type from the dropdown list

The following table describes the labels in this screen. Parameter Description Encapsulation Select your encapsulation type from the dropdown list.

The following table describes the labels in this screen. Parameter Description Username Enter your username for your PPPoE/PPPoA connection. Password

Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled

[Dynamic Route] RIP (Routing Information Protocol): Select this option to specify the RIP version, including RIP1, RIP2-B and RIP2-M. RIP2-B & RIP

3.4.2 LAN Configuration Go to Interface Setup -> LAN. The LAN option enables you to configure the LAN port. There are the IP settings of the LAN

The following table describes the labels in this screen. Parameter Description IP Address Enter the IP address you wish to use with your LAN here.

3.4.2.2.1 DHCP Enable The next screen will vary depending on the DHCP option you selected. The following table describes the labels in this screen.

The following table describes the labels in this screen. Parameter Description DCHP Server IP for Relay Agent Enter the IP address for the DHCP re

3.4.3 Wireless Configuration Go to Interface -> Wireless to setup the wireless parameters. This section introduces the wireless LAN and some basic

interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS T

802.11b+g+n – It allows 802.11b, 802.11g, and 802.11n wireless network client to connect this router (maximum transfer rate 11Mbps for 802.11b client

Guard Interval It is one of several draft-n features designed to improve efficiency. Select 400nsec to provide a shorter delay between transmission f

network. Use WPS Select "Yes" to enable WPS function, Select "No" to disable WPS. 3.4.3.4 WPS Settings Wi-Fi Protected Setup (

Table of Contents 1 Introduction...

this wireless router is enabled, you’ll see "Configured" message here. If wireless security function has not been set, you’ll see "Unco

building the connection. 3.4.3.5 Wireless Authentication The following table describes the labels in this screen. Parameter Description WEP-64Bi

please select the encryption method (TKIP or AES) and enter 8-63 ASCII characters or 64 hexadecimal characters as the "Pre-Shared Key". 3.4.

3.5 Advanced Setup 3.5.1 Firewall Go to Advance Setup-> Firewall to set firewall rule. User can enable or disable firewall feature of the ADSL ro

3.5.2 Routing 3.5.2.1 Static Routing Go to Advance Setup-> Routing to see the Routing Table Routing Table List This table lists IP address of Inter

Device Show the interface that go to the next hop (router), such as LAN port. Use The counter for access time. Edit Edit the route, this icon is not s

directly connected networks. Enter a number that approximates the cost for this link. The number need not to be precise, but it must between 1 and 15.

broadcasting while RIP-2M uses multicasting.  Direction: Select the RIP direction from None, Both, In Only and Out Only.  Multicast: IGMP (Interne

The following table describes the labels in this screen. Parameter Description Virtual Circuit (VC) The Virtual Circuit (VC) properties of the ATM

WAN side. When the response comes back, NAT translates the destination address (the inside global address) back to the inside local address before for

3.5.2 Routing ...44 3.5.2.1 Stati

addresses to globally unique ones required for communication with hosts on other networks. It replaces the original IP source address (and TCP or UDP

NAT Mapping Types NAT supports five types of IP/port mapping. They are: a. One-to-One: In One-to-One mode, the TC3162 EVM maps one local IP address to

3.5.3.1 Virtual Server Go to Advanced Setup ->NAT -> Virtual Server to set virtual server as you need. (known as Port Mapping). Use the Virtu

Parameter Description Virtual Server for Show the Virtual Server setting is for single or multiple IP Addresses. Rule Index Choose the rule number. A

The following table describes the labels in this screen. Parameter Description DMZ setting for Show the DMZ setting is for single or multiple IP Ad

The following table describes the labels in this screen. Parameter Description Address Mapping Rule Show the Address Mapping for single or multip

Address Mapping Server Listing This is a listing of all virtual servers your have set.When you are done making changes, click on SAVE to save your cha

3.5.4.1 Rule You can set 16 different QoS rules. Each QoS rule has its detail setting conditions like: 802.1p, application, DSCP, IP, MAC, Protoco

The following table describes the labels in this screen. Parameters Description Rule Index Select 16 different rules, each rule’s detail can be s

Source Mask Set the subnet mask value that you want to filter in source side Source Port Range Set the port range value that you want to filter in sou

Appendix A: Glossary...85

3.5.5 VLAN Go to Advanced Setup ->VLAN to set VLAN settings. A Virtual LAN (VLAN) is a switched network logically segmented by functions, project t

3.5.5.1 Assign VLAN PVID For Each Interface The following table describes the labels in this screen. Parameter Description ATM VC #0: PVID Enter the

ATM VC#7 Ethernet Port #1: PVID Enter the PVID number you wish to assign to Ethernet Port #1 Ethernet Port #2: PVID Enter the PVID number you wish to

The following table describes the labels in this screen. Parameter Description VLAN Index The number of the index is determined by the model or IC.

3.5.6 ADSL Go to Advanced Setup ->ADSL to set different ADSL connection The following table describes the labels in this screen. Parameter Des

3.6 Access Management 3.6.1 ACL Go to Access Management -> ACL to enable remote management. Access Control Listing (ACL) is a management tool that

ACL Rule Index: This is the item number to record the setting rule. Active Once you choose "Yes " then you can access the IP via router. Sec

The following table describes the labels in this screen. Parameter Description IP/MAC Filter Set Index This is the item number to record the settin

network application over another such as 21 is for FTP service. The port number range is from 0 to 65535. It is recommended that this option be config

3.6.2.2 Application Filter The following table describes the labels in this screen. Parameter Description Application Filter Activate or deactivate

1 Introduction The PLANET 802.11n Wireless ADSL 2/2+ Router with 2T3R MIMO antenna technology, ADN-4000, provides office and residential users the ide

3.6.2.3 URL Filter The following table describes the labels in this screen. Parameter Description Active Activate or deactivate the URL filter. URL

modem. The host computer is called a management station and the modem is called an SNMP agent. The data that can be accessed via SNMP is stored in a M

How do I know if I'm using UPnP? UPnP hardware is identified as an icon in the Network Connections folder (in Windows XP & Windows ME). Each

SAVE: Click SAVE to save the setting to the ADSL Router. 3.6.5 DDNS Go to Access Management-> DDNS to set DDNS account. The Dynamic Domain Name Sy

My Host Name Type the domain name assigned to your ADSL by your Dynamic DNS provider. E-mail Address Type your e-mail address. Username Type your user

3.6.6 CWMP Go to Access Management-> CWMP to set CWMP parameters. The following table describes the labels in this screen. Parameter Description

3.7 Maintenance 3.7.1 Administration Go to Maintenance-> Administration to set a new user's name and password to restrict management access

server is set, you will only need to set the time zone. If you manually set the time, you may also set Daylight Saving dates and the system time will

information. A Network Time Protocol (NTP) server can automatically set the router time for you. If you use an NTP server, you will only need to sele

The following table describes the labels in this screen. Parameter Description Current Firmware Version The current firmware version will be shown he

ADSL and Internet connection to determine the connection method used by your ISP.  PPPoE, PPPoA, Direct Connection Support Various WAN connections a

Current Settings Factory Default Settings If you wish to restart the router using the factory default settings (for example, after a firmware upgrade

Circuit, click the drop-down list and select the name of the Virtual Circuit on which the system status is to be shown. [Device Information] Firmwa

[ADSL] ADSL Firmware Version: This field displays current ADSL firmware version. Line States: This field displays the ADSL connection process and sta

all entries from the list, click Clear Log. New entries will begin accumulating. If the device is rebooted, the logs are automatically cleared. 3.8

[ADSL] The ADSL screen gives you information about how much data your router has transmitted or received across the ADSL connection. Click on REFRES

Appendix A: Glossary Address mask A bit mask select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the net

CO Central Office. Refers to equipment located at a Telco or service provider's office. CPE Customer Premises Equipment located in a user's

One of the most common local area network (LAN) wiring schemes, Ethernet has a transmission rate of 10 Mbps. FTP File Transfer Protocol. The Internet

IP address The 32-bit address assigned to hosts that want to participate in a TCP/IP Internet. ISP Internet service provider - A company allows home a

PPPoE PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. Re

LAN Features  4-Port Switch The ADN-4000 incorporates a 4-port 10/100BaseT switching hub, making it easy to create or extend your LAN.  DHCP Serve

via TCP/IP protocols. Spanning-Tree Bridge Protocol (STP) Spanning-Tree Bridge Protocol (STP) - Part of an IEEE standard. A mechanism for detecting a

91Telnet The virtual terminal protocol in the Internet suite of protocols - Allows users o