Planet IGT-1205AT Instrukcja Użytkownika

Industrial 10/100/1000Base-T to2 100/1000Base-X SFP Media ConverterIGT-1205ATUser's Manual

102. InstallationThis section describes the functionalities of the Industrial Gigabit Media Converter’s components and guides how to install i

11trafc control cabinets. It also possesses an integrated power supply source with wide range of voltages (12 to 48V DC or 24V A

122.1.1 Converter Front PanelFigure 2-1 shows the front panel of Industrial Gigabit Media Converter.1000 LNK/ACT100 LNK/ACTIGT-1205AT110/

132.1.2 LED IndicatorsSystemLED Color FunctionP1 Green Lit: indicate power 1 has power.P2 Green Lit: indicate power 2 has power.FAULT GreenLit: indic

142.1.3 Converter Upper PanelThe upper panel of the Industrial Gigabit Media Converter consists of one terminal block connector within

152.1.4 Wiring the Power InputsThe 6-contact terminal block connector on the top panel of Industrial Gigabit Media Converter is used f

162.1.5 Wiring the Fault Alarm ContactThe fault alarm contacts are in the middle of the terminal block connector as the picture shows

17The Industrial Gigabit Media Converter has two SFP interfaces that supports 100/1000 dual speed mode (Optional Multi-mode / Single-

18MGB / MFB Series TransceiverFigure 2-3: Plug in the SFP TransceiverApproved PLANET SFP TransceiversPLANET Industrial Gigabit Media Converter

19MGB-LB40SFP-Port 1000Base-LX (WDM, TX:1550nm) mini-GBIC module-40kmMGB-TSXSFP-Port 1000Base-SX mini-GBIC module - 550m (-40~75°C)MGB-TLXSFP-Port 100

TrademarksCopyright © PLANET Technology Corp. 2013.Contents are subject to revision without prior notice.PLANET is a registered trademark of PLA

201. Set the DIP Switch of SFP Port 1 or Port 2 to the “OFF” position with ber speed 1000Base-X.ON OFFPort 1 (DIP 1) 100FX 1000XPort 2 (DIP 2) 100FX

212. Make sure both sides of the SFP transceiver are with the same media type or WDM pair; for example, 100Base-FX to 100Base-FX,

22NoteNever pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with viol

232.2 Mounting InstallationThis section describes how to install the Industrial Gigabit Media Converter and makes connections to it. Please

2412Step 2: Lightly insert the DIN-Rail into the track.Step 3: Make sure the DIN-Rail is tightly secured on the track.Step 4: Please refer to th

2512Step 5: Lightly pull out the bottom of the DIN-Rail from the track to remove.2.2.2 Wall Mount Plate MountingTo install the Industr

263. ApplicationsIn this paragraph, we will describe how to install the Industrial Gigabit Media Converter.Transportation NetworkingControl Center

27Installation StepsStep 1: Unpack the Industrial Gigabit Media Converter.Step 2: Check whether the DIN-Rail is screwed on the Industrial Gi

284. TroubleshootingThis chapter contains information to help you solve issues. If the Industrial Gigabit Media Converter is not funct

295. Cable Connection ParametersThe wiring details are as below:100FX Fiber Optical Cables:Standard Fiber Type Cable Specication100Base-FX(1300nm)Mul

CE Mark WarningThis is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be

30APPENDIX A: Networking ConnectionA.1 Converter’s RJ-45 Pin Assignments1000Mbps, 1000Base-TContact MDI MDI-X1 BI_DA+ BI_DB+2 BI_DA- BI_DB-3 BI_DB+ BI

31A.2 RJ-45 Cable Pin AssignmentsThe standard RJ-45 receptacle/connectorThere are 8 wires on a standard UTP/STP cable and each wire is col

EC Declaration of ConformityFor the following equipment: *Type of Product : Industrial 10/100/1000Base-T to 2 100/1000Base-X SFP Media Converter (

Table of Contents1. Introduction ... 5 1.1 Package Contents ...

51. Introduction1.1 Package ContentsCheck the contents of your package for the following parts:Industrial Gigabit Media Converter x 1 lUser's Ma

61.3 Product FeaturesPhysical Port 1-port 10/100/1000Base-T RJ-45 with auto MDI / MDI-X function 2 SFP interfaces, 100/1000Base-X dual mode (DIP sw

7 When Primary-Port link fails, the trafc will swap to Backup-Port automatically Once the Primary-Port status is back to link up, the

8Network Cables10/100/1000Base-T :Cat. 3, 4, 5, 5e, 6 UTP cable (100meters, max.)EIA/TIA-568 100-ohm STP (100meters, max.)1000Base-SX :50/125μm or 62.

91.5 Physical DimensionsIGT-1205AT Industrial Gigabit Media Converter dimensions (W x D x H): 135 x 87 x 32mmSide ViewBottom ViewFront ViewM